早在20 世紀60 年代，國外發達國家就對裝車、裝船過程蒸發損耗油氣進行回收技術的研究，20 世紀70 年代，歐美等國已廣泛應用油氣回收技術于裝車、裝船等過程。在油氣回收方面，歐盟各國都做出了明確的規定，有的國家還對加裝了油氣回收裝置的油庫和加油站實行階段性的財政補貼或稅收減免的優惠。

　　As early as the 1960s, developed countries abroad conducted research on the recovery technology of oil and gas evaporated during loading and shipping processes. In the 1970s, oil and gas recovery technology was widely used in loading and shipping processes in Europe, America, and other countries. In terms of oil and gas recovery, EU countries have made clear regulations, and some countries have also implemented phased financial subsidies or tax exemptions for oil depots and gas stations equipped with oil and gas recovery devices.

　　我國于2020年12月發布了《儲油庫大氣污染物排放標準》（GB20950-2020）、《油品運輸大氣污染物排放標準》（GB20951-2020）、《加油站大氣污染物排放標準》（GB20952-2020），并于2021年4 月1 日開始實施。根據《儲油庫大氣排放標準》的要求，裝油時產生的油氣應進行密閉收集和回收處理，經過回收處理的油氣排放濃度要達到≤25g/m?(非甲烷總烴)，處理效率要≥95%。

　　China released the "Emission Standards for Air Pollutants from Oil Storage Tanks" (GB20950-2020), "Emission Standards for Air Pollutants from Oil Transport" (GB20951-2020), and "Emission Standards for Air Pollutants from Gas Stations" (GB20952-2020) in December 2020, and implemented them on April 1, 2021. According to the requirements of the "Atmospheric Emission Standards for Oil Storage Tanks", the oil and gas generated during oil loading should be collected and recovered in a closed manner, and the concentration of the recovered oil and gas emissions should reach ≤ 25g/m? (Non methane total hydrocarbons), the processing efficiency should be ≥ 95%.

　　油氣回收設備是用于收集和處理揮發性有機化合物（VOCs）和油氣的專用裝置；是對原油、汽油、柴油、石腦油等油品；甲醇、乙二醇等醇類；苯、甲苯、二甲苯等苯類以及其他揮發性有機物在儲存、運輸過程中揮發的油氣對進行處理。這部分油氣對環境、人們的健康和安全生產越來越引起人們的重視。

　　Oil and gas recovery equipment is a specialized device used for collecting and processing volatile organic compounds (VOCs) and oil and gas; It refers to oil products such as crude oil, gasoline, diesel, and naphtha; Alcohols such as methanol and ethylene glycol; The oil and gas evaporated from benzene, toluene, xylene and other volatile organic compounds during storage and transportation should be treated. This part of oil and gas is increasingly attracting people's attention to the environment, people's health, and safety production.

　　油氣回收的設計根據業主方提供的條件和要求進行設計，比如：鶴管裝車量和罐區的儲量等要求確定油氣回收的處理量比如：30～2000m?/h；也要根據業主提供的介質成分來確定油氣回收的處理工藝,如：冷凝法、吸附法、吸收法、膜吸附法、或者多種工藝組合等方法。

　　The design of oil and gas recovery is based on the conditions and requirements provided by the owner, such as the loading capacity of crane pipes and the storage capacity of tank areas. The processing capacity of oil and gas recovery is determined, such as 30-2000m ?/h; The treatment process for oil and gas recovery should also be determined based on the medium composition provided by the owner, such as condensation method, adsorption method, absorption method, membrane adsorption method, or a combination of multiple processes.

　　設計依據：（1）業主方提供的所有設計條件、技術要求；

　　Design basis: (1) All design conditions and technical requirements provided by the owner;

　?。?）國家相關規范和標準

　　(2) National regulations and standards

　　《油氣回收處理設施技術標準》GB 50759-2022

　　Technical Standard for Oil and Gas Recovery and Treatment Facilities GB 50759-2022

　　《大氣污染物綜合排放標準》GB16297-1996

　　Comprehensive Emission Standards for Air Pollutants GB16297-1996

　　《爆炸性氣體環境用電氣設備》GB3836-2000

　　Electrical Equipment for Explosive Gas Environments GB3836-2000

　　《爆炸和火災危險環境電力裝置設計規范》GB50058-92

　　Code for Design of Electrical Installations in Explosive and Fire Hazardous Environments GB50058-92

　　《火災自動報警系統設計規范》GB50116-2008

　　Design Specification for Automatic Fire Alarm System GB50116-2008

　　《工業金屬管道設計規范》GB50316-2000(2008年版)

　　Design Code for Industrial Metallic Piping GB50316-2000 (2008 edition)

　　《石油化工企業燃料氣系統和可燃性氣體排放系統設計規范》SH3009-2001

　　Design Specification for Fuel Gas System and Combustible Gas Emission System in Petrochemical Enterprises SH3009-2001

　　《石油化工企業設計防火規范》GB50160-2008

　　Fire Protection Design Code for Petrochemical Enterprises GB50160-2008

　　《石油化工靜電接地設計規范》SH3097-2000

　　Design Specification for Static Electricity Grounding in Petrochemical Industry SH3097-2000

　　《石油化工自動化儀表選型設計規范》SH3005-1999

　　Specification for Selection and Design of Automation Instruments in Petrochemical Industry SH3005-1999

　　《低壓配電設計規范》GB50054-2011

　　Code for Design of Low Voltage Distribution GB50054-2011

　　《通用用電設備配電設計規范》GB50055-2011

　　Design Code for Distribution of General Electrical Equipment GB50055-2011

　　《儲油庫大氣污染物排放標準》（GB20950-2020）

　　Emission Standards for Air Pollutants from Oil Storage Tanks (GB20950-2020)

　　《油品運輸大氣污染物排放標準》（GB20951-2020）

　　Emission Standards for Air Pollutants from Oil Transport (GB20951-2020)

　　安全附件：

　　Security attachments:

　?。?）、油氣回收裝置入口設置阻火器、出口設置阻火透氣帽；

　　(1) Install flame arresters at the inlet and breathable caps at the outlet of the oil and gas recovery device;

　?。?）、油氣回收裝置內部設置點型可燃氣體探測器（報警儀），氣體泄漏時報警；

　　(2) A point type combustible gas detector (alarm) is installed inside the oil and gas recovery device to sound an alarm in case of gas leakage;

　?。?）、設備設有接地裝置、防雷裝置及等電位防靜電跨接；

　　(3) The equipment is equipped with grounding devices, lightning protection devices, and equipotential anti-static cross connections;

　?。?）、電機、儀表等均采用防爆型，整機防爆；

　　(4) The motors, instruments, etc. are all explosion-proof, and the whole machine is explosion-proof;

　?。?）、吸附罐設置溫度傳感器，當活性炭溫度超過設定值時報警；

　　(5) The adsorption tank is equipped with a temperature sensor, which will sound an alarm when the temperature of the activated carbon exceeds the set value;

　　（6）、設置緊急排放裝置，油氣回收系統故障時可臨時排放以免耽誤裝車。

　　(6) Set up emergency discharge devices to temporarily discharge oil and gas recovery systems in case of malfunction, in order to avoid delaying loading.

　　工藝原理及運行控制

　　Process principle and operation control

　　(1)引氣工藝

　　(1) Air entraining process

　　依次加裝阻火器、采樣口手動球閥、溫度傳感器、壓力感測器及引氣風機等儀表、閥門及設備。

　　Install instruments, valves, and equipment such as flame arresters, manual ball valves for sampling ports, temperature sensors, pressure sensors, and induced draft fans in sequence.

　　(2)制冷工藝：

　　(2) Refrigeration process:

　　a.待處理的尾氣依次經過各個冷段。其中a段的工作原理是利用b段制冷后的低溫尾氣進行冷量交換利用，實現能量再利用。

　　a. The exhaust gas to be treated passes through each cold section in sequence. The working principle of section A is to use the low-temperature exhaust gas cooled by section B for cold exchange and utilization, achieving energy reuse.

　　b.尾氣回收裝置冷凝系統采用將各個制冷段組合成整體形式，減少整個尾氣回收裝置的冷凝箱的體積并減少管路冷量損失，大大提高制冷效率和降低能耗。

　　b. The condensation system of the exhaust gas recovery device adopts the combination of various refrigeration sections into a whole form, reducing the volume of the condensation box of the entire exhaust gas recovery device and minimizing the loss of pipeline cooling capacity, greatly improving refrigeration efficiency and reducing energy consumption.

　　c.尾氣經過最后冷凝段后進入吸附罐處理。

　　c. After passing through the final condensation section, the exhaust gas enters the adsorption tank for treatment.

　　d.選用知名某品牌制冷壓縮機組進行多重制冷，整套系統可以根據尾氣量處理的負荷大小自動調節，節省能耗。

　　d. Selecting a well-known brand of refrigeration compressor unit for multiple refrigeration, the entire system can automatically adjust according to the load size of exhaust gas treatment, saving energy consumption.

　　e. 制冷過程的壓縮機組包括其他的電氣設備以及相配套的信號柜，動力柜等設備都被裝置在橇中。橇外殼采用不銹鋼材料，安全性能高。

　　e. The compressor unit for the refrigeration process, including other electrical equipment and supporting signal cabinets, power cabinets, and other equipment, is installed in the sled. The sled shell is made of stainless steel material, which has high safety performance.

　　(3)冷凝液收集過程：

　　(3) Collection process of condensate:

　　a.經過制冷過程后，尾氣中的組分被冷凝成混合物被送至儲罐中。

　　a. After the refrigeration process, the components in the exhaust gas are condensed into a mixture and sent to the storage tank.

　　b.回收得到的回收液可以直接利用管道泵輸送至業主方罐區。

　　b. The recovered liquid can be directly transported to the owner's tank area through pipeline pumps.

　　c.回收泵根據儲液罐的液位元信號自動開、停。

　　c. The recycling pump automatically starts and stops based on the liquid level signal of the storage tank.

　　(4)吸附過程

　　(4) Adsorption process

　　a.尾氣中不能被完全冷凝的少量輕組分進入吸附罐利用尾氣回收專用的吸附劑進行吸附處理

　　a. A small amount of light components in the exhaust gas that cannot be completely condensed enter the adsorption tank and are treated with specialized adsorbents for exhaust gas recovery

　　b.吸附工藝采用兩套吸附罐切換循環工作，當一個吸附罐的中的吸附劑對尾氣尾氣進行吸附處理時，另一個吸附罐中則利用真空泵進行脫附處理，脫附的富集尾氣再送至冷凝段進行回收處理。

　　b. The adsorption process uses two sets of adsorption tanks to switch between cyclic operation. When the adsorbent in one adsorption tank adsorbs the tail gas, the vacuum pump is used in the other adsorption tank for desorption treatment. The desorbed enriched tail gas is then sent to the condensation section for recovery treatment.

　　c.吸附專用的真空泵選用干式渦旋真空泵，此真空泵具有被抽物料可循環使用、無油無水無污染、能耗低，真空度高，噪音小、免維護等優點。

　　c. The vacuum pump used for adsorption is a dry vortex vacuum pump, which has the advantages of reusable materials, oil-free, water free, pollution-free, low energy consumption, high vacuum degree, low noise, and maintenance free.

　　(5)排放過程

　　(5) Emission process

　　a.經過吸附處理后的尾氣已達排放標準，通過排放管道排放。

　　a. After adsorption treatment, the exhaust gas has reached the emission standard and is discharged through the discharge pipeline.

　　b.排空處加裝尾氣濃度監測取樣口，方便隨時抽取尾氣樣本。

　　b. Install a tail gas concentration monitoring sampling port at the exhaust outlet to facilitate the extraction of tail gas samples at any time.

　　進氣口溫度測定點設置位置為引氣風機前管段，采用溫度傳感器將溫度實時傳送PLC信號控制工藝運行。

　　The temperature measurement point for the air inlet is set at the front pipe section of the induced draft fan, and a temperature sensor is used to transmit the temperature in real time to the PLC signal to control the process operation.

　　由于油氣回收設備為撬裝設備，安裝簡單，做整體防爆處理、設備運營安全，系統可以全自動運行，給設備送上電后就無需人工干預；PLC系統預留RS485標準通訊口，可接業主的電腦（如有）遠程監控設備運行狀態。

　　Due to the fact that the oil and gas recovery equipment is a pry mounted device, it is easy to install, undergoes overall explosion-proof treatment, and operates safely. The system can operate fully automatically, and there is no need for manual intervention after powering on the equipment; The PLC system reserves RS485 standard communication port, which can be connected to the owner's computer (if any) for remote monitoring of equipment operation status.

　　本文由  油氣回收設備 友情奉獻.更多有關的知識請點擊  http://www.www.ralizheng.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from oil and gas recovery equipment For more related knowledge, please click http://www.www.ralizheng.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.